|
Post by Snipersmudge on May 1, 2023 17:29:04 GMT
Nice mate like it.
|
|
|
Post by Robbo on May 1, 2023 18:06:36 GMT
|
|
|
Post by Robbo on May 1, 2023 18:07:17 GMT
Thanks Smudge, didn't see you there
|
|
|
Post by Ian H. on May 1, 2023 20:52:40 GMT
Looking awesome, Robbo!
|
|
|
Post by tommygunn on May 2, 2023 3:27:49 GMT
Looking very smooth and sharp.
|
|
|
Post by Robbo on May 2, 2023 8:48:26 GMT
Thanks fellas
|
|
|
Post by Robbo on May 2, 2023 14:39:34 GMT
I've just given my exhausts a coat of Vallejo steel i'll give them a wash when they are dry
|
|
|
Post by Boots on May 2, 2023 18:28:19 GMT
Lookin` very nice mate
|
|
|
Post by Robbo on May 2, 2023 19:26:16 GMT
Thank you Kindly
|
|
|
Post by Paul B on May 3, 2023 7:05:41 GMT
Very smart those paints and the job be Ian
|
|
|
Post by Robbo on May 3, 2023 11:31:07 GMT
Thank you Mr B I decided to get it all together before Klear goes on and decals, hope I don't regret it
|
|
|
Post by tommygunn on May 3, 2023 13:01:17 GMT
Well smart.
|
|
|
Post by Robbo on May 3, 2023 13:25:11 GMT
Well thank you kindly
|
|
|
Post by Robbo on May 3, 2023 15:55:28 GMT
Tiffy has got the Klear coat on now, I'll spare you a photo but I can now do the decals tomorrow
Right a question for you. I was using my Neo to put the clear on and it was working fine but there was tiny air bubbles coming out of the trigger/finger button. I thought it might be an O ring but last time I had that happen it didn't come out of the trigger it bubbled up in the cup and nothing was coming out of the end but it is this time, iss it something different, it still works fine other than the bubbles?
|
|
|
Post by Robbo on May 3, 2023 16:48:15 GMT
I got a photo as I know you lot like them
|
|
|
Post by Armorguy on May 3, 2023 16:49:47 GMT
Smooth !
|
|
|
Post by Robbo on May 3, 2023 16:55:54 GMT
Doesn't look so dry now does it Guy?
|
|
|
Post by Paul B on May 3, 2023 17:22:47 GMT
Nice shiny coat, now for the stickers.... or maybe better tomorrow
|
|
|
Post by Robbo on May 3, 2023 17:28:21 GMT
Tomorrow You're like me, eager to keep moving
|
|
|
Post by Boots on May 3, 2023 19:25:40 GMT
Nice one Robbo As for the AB.....i stopped putting Klear thru the AB.....normally bubbles coming back is caused by a restrction of some sort at the needle seat end, a bit like when you put ya finger over the end and open the trigger.....bubbles will surface coz it`s got no-where to go. I use to AB it and encountered similar (maybe not the same) issues even tho i`d flushed the AB thoroughly thru after spraying.....i stripped and cleaned all the parts with a cleaning set and found small particles of varnish,once cleand it worked fine.....now i just use a branded varnish/thinner mix. Might not be the answer to ya problems but worth doing a thorough deep clean just to check.....i run mine thru the cleaner about 8 times on the longest setting and let ya fluid get a bit warm.....i`m no AB expert trust me
|
|