|
Post by Ian H. on Jul 1, 2020 23:00:50 GMT
|
|
|
Post by Paul B on Jul 2, 2020 3:59:28 GMT
Lovely little aircraft there Ian  . Hope the ride goes well this time 
|
|
|
Post by PorcoRosso on Jul 2, 2020 19:09:55 GMT
Great choice Ian.
|
|
|
Post by Marco on Jul 3, 2020 18:48:43 GMT
You never stop, don't you? Nice choice mate!
|
|
|
Post by Snipersmudge on Jul 4, 2020 11:11:16 GMT
great choice, watching with interest.
|
|
|
Post by JEFF on Jul 4, 2020 19:18:55 GMT
There ya go, Ian. Great choice, Lad. 
|
|
|
Post by Boots on Jul 5, 2020 20:06:31 GMT
Great choice bud and lets hope this Hobbyboss one doesn`t become `unBEARable` 
|
|
|
Post by Ian H. on Jul 6, 2020 1:43:49 GMT
Thanks guys! Let's see what "plastastrophe" HobbyBoss has in store for me.
|
|
|
Post by Ian H. on Aug 4, 2020 15:50:29 GMT
|
|
|
Post by Paul B on Aug 4, 2020 17:17:08 GMT
Looking darned good Ian 
|
|
|
Post by SteveM on Aug 4, 2020 18:12:30 GMT
Nicely detailed kit by the looks of it, it’ll be great in your hands buddy 
|
|
|
Post by Boots on Aug 4, 2020 18:22:19 GMT
Lovely start Ian 
|
|
|
Post by Ian H. on Aug 4, 2020 19:10:39 GMT
Thanks, gents! I will give HB credit where credit is due and the gunsight they provide in the kit is probably one of the best I have seen in a prop kit.
|
|
|
Post by Paul B on Aug 4, 2020 19:23:06 GMT
Sounds like Hobby Boss should stick to aircraft then 
|
|
|
Post by Ian H. on Aug 4, 2020 20:13:32 GMT
No doubt, Paul, 'cause that Olifant is an abortion.🤣🤣🤣🤣
|
|
|
Post by Robbo on Aug 4, 2020 22:07:23 GMT
I’m in nice and early for a change. Cracking start sir
|
|
|
Post by Ian H. on Aug 4, 2020 22:45:00 GMT
Glad to have you aboard, Robbo!
|
|
|
Post by Marco on Aug 5, 2020 16:40:09 GMT
Ian, great paint work! Me likes a lot!
|
|
|
Post by Ian H. on Aug 5, 2020 20:28:12 GMT
Thanks, Marco! After having had a rather bad past six weeks and a Mo-Jo slow-down myself, I have found this kit to be a real morale booster; a simple build which will be rounded out with a mono-chromatic paint scheme. Once again, I will give HB their due on this one as it has been a joy to build. I got the fuselage together and there were no problems there, other than having to shave a few mm's off the dashboard so the halves would join. I got the fuselage seams sanded and the only thing I added were two sheet stock strakes on the rear lower fuselage to replace the kit strakes since the seam ran down the middle of them and that would have been tough to fill. I was holding my breath for the wing fit but once again perfect fit and the wings joined the fuselage perfectly with no filling needed. I just have a few spots to clean up and then it will be time for primer. Regards, Ian    
|
|
|
Post by Marco on Aug 5, 2020 21:03:33 GMT
Nice work Ian! Looks great! Fast build!
|
|